Super Power Amplifier Yiroshi Audio - 1000 Watt
This Yiroshi audio power amplifier has a low character and has high power output , so many audio lovers choose this type of amplifier because the bass boom is very pronounced. To make this Yiroshi audio amplifier so powerful need a power supply which is sufficient to let the results that can at maximum transformer minimum 20A 45-75v output and the good quality of components.
Below the circuit diagram of Yiroshi audio power amplifier driver + final transistors:
Resistor
R1=2k2, R2=47k, R3=100R, R4=100R, R5=56R, R6=56R, R7=56R, R8=56R, R9=47k, R10=100R, R11=2k2, R12=2k2, R13=100R, R14=47K, R15=2k2, R16=2k2, R17=100R, R18=100R, R19=100R, R20=100R, R21=220R/1W, R22=220R/1W, R23=100R, R24=1k8, R25=1k, R26=10k, R27=56R, R28=56R, R29=100R/1W, R30=100R/1W, R31=120R/1W, R32=120R/1W, R33=100R, R34=100R, R35
Capacitor
C1=1u Nonpolar, C2=330pF, C3=4n7, C4=4n7, C5=100uF/100V, C6=100uF/100V, C7=330uF/50V, C8=12pF, C9=12pF, C10=100N, C11=47pF, C12=150pF, C13=150pF, C14=100N
Transistor
Q1,Q4,Q7,Q8=2N5401
Q2,Q3,Q5,Q6=2N5551
Q9
Q10
Q11=MJE340
Q14=TIP2955/2SA1962
Q15=TIP3055/2SC5242
Q16
Q23
Final Power Transistor Audio Amplifier List
2SC5200/2SA1943 : 230volt 15 ampere 150 watt
2N3055/MJ2955 : 100
TIP3055/TIP2955
2N3773/2N6609 : 160volt 16 ampere 160watt
MJ15003/04
MJ15024/25
Toshiba 2SA1095/2SC2565 : 160volt 15 ampere 150watt
2SC5200/2SA1943 : 230volt 15 ampere 150 watt
2N3055/MJ2955 : 100
TIP3055/TIP2955
2N3773/2N6609 : 160volt 16 ampere 160watt
MJ15003/04
MJ15024/25
Toshiba 2SA1095 / 2SC2565 : 160volt 15 ampere 150watt
2SA1103 / 2SC2578 : 100volt 7 ampere 70 watt
2SA1105 / 2SC2577 : 120volt 9 ampere 90watt
2SA1106 / 2SC2851 : 140volt 10 ampere 100watt
2SC2580 / 2SA1105 : 120volt 9 ampere 90watt
2SC2581 / 2SA1106 : 140volt 10 ampere 100watt
Buy these parts, go to Allchips.
PCB Layout Driver Power Amplifier Yiroshi Audio
PCB Parallel Final Power Transistor 7 Set Toshiba 2SC5200 2SA1943
Final Power Transistor Assembling 2SC5200 and 2SA1943
Wiring Diagram Driver Power Amplifier and Final Power Transistor
For this Yiroshi power amplifier project, I make a separate PCB driver with the final transistor, you can see on both picture PCB Layout above. The power amplifier is very good and high performance. You can upgrade again to add power amplifier by adding the final transistor and also replace it with more power, current, and stronger voltage. And also must be balanced with a larger power supply current and voltage. For more details see the full interesting video below:
This circuit have some problems after 4 to 5 min power transistor dead
ReplyDeleteno, please see at circuit diagram. There is no erorr, you must adjust bias voltage.
Deleteit can work normally not just a minute.
DeleteNice projekt and video! :D
ReplyDeletethanks dear...
DeleteGood amplifier and thanks for your video
ReplyDeletethank you, thanks for visit
DeleteThanks for video and project.
ReplyDeleteyoure wellcome, and say thanks for visit
Deletewe are happy to comment here, and we await your komantar in our blog
ReplyDeleteHello,
ReplyDeleteThe amp as shown in schematics will NOT work. Q15 should be NPN type, prrobably TIP3055, although I think this is a bad choice as TIP3055/TIP2955 have Vce max of only 70V.
Cheers
Q14=TIP2955/2SA1962
DeleteQ15=TIP3055/2SC5242
you can choose these transistor
the power amplifier is work, you can see the video testing amplifier
DeleteI saw some other videos the same circuit but there is no trimpot or bias circuit
ReplyDeleteyes, the circuit is no trimpot bias setting.
DeleteBut on the assembling video i saw there is bias tripot I'm confused, but anyway thanks a lot for sharing this powerful amp i will try to build very soon. Thanks a lot god bless..
ReplyDeletetry to use it cause the trimpot can adjust bias voltage if you using any finalt transistor type.
Deletewhat are the sizes of the PCB?
ReplyDeletesee pcb size on elcircuit stereo yiroshi
Deletehai i want pcb and components all so price please my email id: [email protected]
ReplyDeleteyou can contact me sir.
Deletehow to adjust the trimpot in the amplifier driver
ReplyDeleteyou can set output voltage until 0v.
DeleteHi sir romadhon, I'm back after building this power amp it sounds nice even though i tested it on 65v 8.5A so not enough power supply. Im Wondering on the pnp final output power they are warmer than the npn output i have noticed the predriver 2SA1837 for pnp output is warmer also is this normal? Because still sounds good or maybe i will get problems in the future. Please help
ReplyDeleteYou can change the emitter resistor by using 220R 1w. and also the npn transistor
Deletehi how are you can you tell me how to download the PDF, thanks
ReplyDeletethe pdf file is in stereo yiroshi amp post
DeleteSir can i use 90v symmetrical ?
ReplyDeleteyes im using 110V its normally. but you must have larger heatsink
DeleteSir what voltage should I use for 12pairs 5200/2943 transistor output?
ReplyDeleteyou can use up to 100v for more performance
DeleteCan I use IRFP240 and IRFP9240 for this project?
ReplyDeleteIt can't if you use final mosfet. see class d d4k5 its bigger power than this amp. if you want mosfet class d amp
Deletesir i am using with mjl21194,mjl21193 14 pair ? which use driver ..and volt ? ampere ?..
ReplyDeleteyou can use this driver or yamaha PA-2400, 80 upto 100V is recomended try using 20A current transformer ar SMPS circuit.
DeleteThank you sir
ReplyDeleteNice amp sir but sir you use cliping indictor and protection ckt
ReplyDeleteIf i use 8 transistor instead of 14 transistor in the final driver Will the amplifier still work?
ReplyDeletewhat current rating should the L1 coil be
ReplyDeletemax 20A output
DeleteIs it possible to send me better quality PCB, and PCB size, and layout files, also schematic diagram please [email protected]
ReplyDeletesee newest post sir
Deletesee newest post sir
DeleteWhere do I put the trimpot to regulate the OFFSET voltage?
ReplyDeletecan you tell me the base voltages of 1943 and 5200 mine is .1 and .4 mv
ReplyDeleteset the base voltage by adjusting trimpot
Deletecan you tell me the base voltages of 1943 and 5200 mine is .1 and .4 mv
ReplyDeletePuedes pasar el pdf y las medidas exactas de la placa en que parte del diagrama va el trimpot
ReplyDeleteHi sir,how to order the PCB and components parts of 1kwatt amp.
ReplyDeletewhere can I order PCB please, is there a link
ReplyDeletei can't see the sizes of PCB sir ?
ReplyDeletecan u please help me sir.
you just download PDF and print it!
Deleteits actual size print.
hey..I want to buy all the components of this amplifier.. how can I contact u.. my email is [email protected]
ReplyDeletehttps://www.ebay.com.au/itm/123348339586
DeleteSir if i want to put trimpot which should i put there ?ty
ReplyDeleteSee the schematic
DeleteSir can i use in the circuit 10 pairs of final transistors then the speaker out is? Watts and Witch transformer I can use please tell me sir
ReplyDeleteYou can use upto 20A transformer
DeleteCan i use 55ac o 55acv 20 ampere it is ok sir
ReplyDeleteYes you can
DeleteWhat are the size pcb driver
DeleteIts nice sound.what is the best vac in power amp i have 7 set of 2sc5200 and 7set of 2sa1943 what is the best amphers and Vac 45 something?
ReplyDeleteHey ' i need purchase this amplifier subwoofer kit ...how purchase ??
ReplyDeletehttps://www.ebay.com.au/itm/123348339586
DeleteDid you sell it?
DeleteYes after I corrected the errors on PCB layout, and found a schematic that was correct, have sold over 350 so far, I also have the Crown XLS 6 fet as well, with corrected schematic and PCB, only sold 275 of the so far
Deletethere is a huge demand for these amplifiers, but a lot of errors, or cannot read schematic, and exaggerating the output wattage...people want the truth, when they purchase, that's what I am doing
ReplyDeleteits so good bro
Deletehola amigo tengo un problema en las resistencias de 220 y 100 ohs se me esta calentando y se terminan quemando como corrijo ese problema
ReplyDeleteschematic diagram doesn't have diodes and ohms for R24 and R25 should be flip. can you update the schematic diagram with trimpot
ReplyDeletetem o kit pra vender?
ReplyDeletePlease,send me this pdf thanks ([email protected])
ReplyDeleteThis is where you get PCB, with all the errors fixed, as the layout from wahyu eko romadhom will only work for approx 3 mins then it destroys itself, here is link to PCB that WORKS https://www.ebay.com.au/itm/123561661498?var=&ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
ReplyDeleteHola disen que ay que cambiar 2 resistensias las lateralrs de 4k7 por 47k
ReplyDeletehow many watts on base on resistors? .25 watts or .5 watts
ReplyDeleteR1=2k2, R2=47k, R3=100R, R4=100R, R5=56R, R6=56R, R7=56R, R8=56R, R9=47k, R10=100R, R11=2k2, R12=2k2, R13=100R, R14=47K, R15=2k2, R16=2k2, R17=100R, R18=100R, R19=100R, R20=100R,
Hi sir i just need to ask where to adjust dc offset of this amp i need to adjust to 0V dc there's only one trimpot but adjust only for the current bias.
ReplyDeleteHi sir i just need to ask where to adjust dc offset of this amp i need to adjust to 0V dc there's only one trimpot but adjust only for the current bias.
ReplyDeleteHi You give file Gerber in email : [email protected] :-s
ReplyDeleteHow to make the 10 uh coil bro
ReplyDeleteExplain the guage of wire and how many turns wanted
Sir it working but humming problems and transistors hitting very quickly
ReplyDeletePlease solve the problem sir
In the drawing of squematic,the Q15 transistor isn't wrong?
ReplyDeleteDor,
ReplyDeleteCan you please Tell us where tô find a correct esquematic whith ALL the erros fixed.
After few minuts It burns!
In the squematic there os no trim por, Q15 os misdrawed, André i real life ,some resistores must vê chances.
Thank You Very much!!!!!
do you have available pcb layout for project,.,can i buy?
ReplyDeleteSir....Can you reply... What is the PCB size...???
ReplyDeleteIn the squematic there os no trim por, Q15 os misdrawed, André i real life ,some resistores must vê chances. no, please see at circuit diagram. There is no erorr, you must adjust bias voltage.
ReplyDeletecan you send me Gerber files sir.
ReplyDeletecan i use TTC5200 in exchnge 2sc5200
ReplyDeletepor los comentarios y lo visto otro MAS QUE NO SIRVE CERO Y VAN DOS si es que funciona deberias contestar dudas no creo que te cueste mucho trabajo y tener mas atencion con tus seguidores
ReplyDeleteSir. I make 1000w mono amplifire using this driverboard. I want to use subwoofers on it. What can i do for it?
ReplyDeleteHave a reference blog / idol blog. Important for a blogger to have a reference Take for example, I like a blogger on this site.
ReplyDeleteHave a reference blog / idol blog. Important for a blogger to have a reference Take for example, I like a blogger on this site.
ReplyDeletedo you have preamp of yiroshi amplifier ?
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteWhat exactly is the quiet current in the yiroshi amplifier?
ReplyDeletethis amp has a trap door, replace the components with the xls602
ReplyDeleteeste amplificador tiene una trampita, reemplace los componentes por los de la xls602
After reading all the comments was the above schematic corrected
ReplyDelete